Process Engineering White Papers

261-280 of 360 < first | | | last >
  • Cybersecurity: Power Industry Locks Down

    The power industry is susceptible to a variety of cyber threats, which can wreak havoc on control systems. Management, engineering and IT must commit to a comprehensive approach that encompasses threat prevention, detection and elimination.

    Power Engineering
    03/27/2006
  • Process Control Network Security

    This document provides an understanding of intrusion detection and prevention systems, why they are necessary, how and where they fit in the control system environment, and gives example scenarios.

    Invensys
    03/27/2006
  • V-Cone flow meter test results | Chemical Processing

    The American Petroleum Institute Manual of Petroleum Measurement Standards published the results of flow meter tests at the Southwest Research Institute and Utah State University.

    Southwest Research Institute
    03/21/2006
  • Use CFD to Improve Crystallization | Chemical Processing

    In this article, Kumar Dhanasekharan, Ph.D., technical specialist with the computational fluid dynamics (CFD) specialist Fluent, Inc., shows how modelling crystallizers using CFD can help improve process understanding, control crystal size distribution (CSD) and improve pharmaceutical crystallization results.

    Fluent
    03/06/2006
  • Fieldbus and remote I/O system comparison

    Nine manufacturers participated in the FuRIOS study, which was conduced under the lead of an end user company that compared its use of fieldbus and remote I/O in full detail.

    Aventis, Infraserv GmbH
    02/10/2006
  • Aseptic PAT and Particle Monitoring

    In this white paper, Mark Hallworth, pharmaceutical manager for Particle Measuring Systems, discusses continuous monitoring methods, how they’re evolving, and why they’re important.

    Particle Measuring Systems
    02/06/2006
  • The Regional Transport of Ozone

    EPA tracks emissions of six principal air pollutants - carbon monoxide, lead, nitrogen oxides, particulate matter, sulfur dioxide, and volatile organic compounds. All have decreased significantly since passage of the Clean Air Act in 1970 - except for nitrogen oxides.

    EPA
    01/31/2006
  • Process Control Network Security - Reference Architecture

    This document describes best practices for the reference architecture for a process control system network and its interfaces to a corporate network. The paper’s objective is to give the reader an understanding of the techniques utilized to securely connect these networks.

    Invensys
    01/11/2006
  • Design Tips for Sensing Probes

    This application note from Delta Controls outlines selection and installation criteria for using admittance probes to monitor the level of powders, liquids and other materials. Dielectric constants of more than 200 materials are included.

    Delta Controls
    01/05/2006
  • Clean Compressed Air

    Good air preparation should consider the energy consumption of the system and air treatment equipment.

    Norgren
    11/27/2005
  • Continuous imaging fluid particle analysis: A Primer

    This paper looks at the issues associated with fluid particle analysis, discusses some of the historical methods used, and introduces a new technology: the continuous imaging fluid particle analyzer.

    Fluid Imaging Technologies
    11/14/2005
  • Accurate liquid phase density on aerated liquids

    This white paper discusses SONAR-based, clamp-on gas volume fraction meters which recently have been introduced to the industry that provide an accurate, real time, measurement of entrained gases. Coupling entrained gas volume fraction monitor with most types of process density meters, enables accurate determination of liquid and the liquid-solid components of aerated mixtures.

    10/18/2005
  • Specifying industrial fieldbus networks for automation

    Automation designers face many challenges and tradeoffs in the development of a successful network solution. This white paper discusses the necessary choices in selecting a network technology appropriate for various specific applications.

    Texas Instruments
    10/12/2005
  • Measurement Best Practices

    This 9-page PDF discusses way in which you can ensure your measurements are accurate, repeatable and reliable.

    Rosemount
    10/05/2005
  • Energy Efficiency - The Other Alternative Fuel

    Proven methods for industry to reduce energy consumption and environmental impact are already at hand. These cost-effective solutions promise substantial return-on-investment now and in the future, without sacrificing performance or quality. For most companies and organizations, the answers to maintaining a competitive edge in this era of rising energy costs are readily available. By applying a suite of cost-effective power and automation solutions from technology leaders like ABB, these facilities can achieve substantial energy savings today without waiting for the "alternative fuels" of the future.

    ABB
    09/27/2005
261-280 of 360 < first | | | last >