2006

New page content.
1-20 of 24 < first | prev | | last >
  • Design Tips for Sensing Probes

    This application note from Delta Controls outlines selection and installation criteria for using admittance probes to monitor the level of powders, liquids and other materials. Dielectric constants of more than 200 materials are included.

    Delta Controls
    01/05/2006
  • Process Control Network Security - Reference Architecture

    This document describes best practices for the reference architecture for a process control system network and its interfaces to a corporate network. The paper’s objective is to give the reader an understanding of the techniques utilized to securely connect these networks.

    Invensys
    01/11/2006
  • The Regional Transport of Ozone

    EPA tracks emissions of six principal air pollutants - carbon monoxide, lead, nitrogen oxides, particulate matter, sulfur dioxide, and volatile organic compounds. All have decreased significantly since passage of the Clean Air Act in 1970 - except for nitrogen oxides.

    EPA
    01/31/2006
  • Aseptic PAT and Particle Monitoring

    In this white paper, Mark Hallworth, pharmaceutical manager for Particle Measuring Systems, discusses continuous monitoring methods, how they’re evolving, and why they’re important.

    Particle Measuring Systems
    02/06/2006
  • Fieldbus and remote I/O system comparison

    Nine manufacturers participated in the FuRIOS study, which was conduced under the lead of an end user company that compared its use of fieldbus and remote I/O in full detail.

    Aventis, Infraserv GmbH
    02/10/2006
  • Use CFD to Improve Crystallization | Chemical Processing

    In this article, Kumar Dhanasekharan, Ph.D., technical specialist with the computational fluid dynamics (CFD) specialist Fluent, Inc., shows how modelling crystallizers using CFD can help improve process understanding, control crystal size distribution (CSD) and improve pharmaceutical crystallization results.

    Fluent
    03/06/2006
  • V-Cone flow meter test results | Chemical Processing

    The American Petroleum Institute Manual of Petroleum Measurement Standards published the results of flow meter tests at the Southwest Research Institute and Utah State University.

    Southwest Research Institute
    03/21/2006
  • Cybersecurity: Power Industry Locks Down

    The power industry is susceptible to a variety of cyber threats, which can wreak havoc on control systems. Management, engineering and IT must commit to a comprehensive approach that encompasses threat prevention, detection and elimination.

    Power Engineering
    03/27/2006
  • Process Control Network Security

    This document provides an understanding of intrusion detection and prevention systems, why they are necessary, how and where they fit in the control system environment, and gives example scenarios.

    Invensys
    03/27/2006
  • Chemical Hazard Communication

    Under the provisions of the Hazard Communication Standard, employers are responsible for informing employees of the hazards and the identities of workplace chemicals to which they are exposed.

    OSHA
    03/28/2006
  • Clean-in-place operation for thin-cake filtration technologies

    This article discusses the choice of thin-cake (2 – 25 mm) separation technologies and their benefits to optimizing the effectiveness of the production process. The paper continues with a discussion of clean-in-place operations to meet current Good Manufacturing Practices (cGMP) guidelines including riboflavin test and validations.

    BHS-Filtration
    04/20/2006
  • White Paper: Internet Access in a Process Control Environment

    Industrial automation is no longer limited by the walls of a production facility. More and more automation is being handled via remote communication, whether it’s from the office or from the comfort of your own home. Today’s PLCs give you the ability to access your control system to handle such tasks as monitoring via a website to determine the condition of a machine or check other statistics.

    Wago Innovative Connections
    04/24/2006
  • Preventing Segregation During Powder Drying

    This 4-page case history by Jeroen van den Berg of Bolz-Summix discusses how changing process conditions within a conical screw dryer eliminated granulation and minimized product segregation.

    Bolz-Summix
    05/02/2006
  • Securing Batch Control Systems

    Batch process control security is becoming a critical concern for the process control domain, IT technology infrastructure and the business enterprise. This paper explores several key security concerns in batch control system architectures and methods for addressing these issues.

    Honeywell
    05/11/2006
  • Guidance note for environmental safety instrumented systems

    Safety Instrumented Systems (SIS) are designed to monitor the process and control outputs to prevent or mitigate hazardous events. The design process strives for inherent safety, which is enhanced by applying multiple independent safety layers. Learn how to prevent accidents with prevention layers and minimise the consequences with mitigation layers.

    P & I Design
    05/26/2006
  • Managing Complex Equipment Status in a GMP Environment

    Batch manufacturing systems must maintain the status of equipment, including which are available, dirty, out of service, etc. In industries that enforce Good Manufacturing Practices (GMPs), additional status types and values for process equipment must be maintained. Rules associated with the equipment status can be complex and involve the equipment class, current equipment state and time in the current state. This paper covers the operator interface used to review the equipment status and the interlocking requirements between the recipe and batch phases based on multiple status types.

    Honeywell
    06/13/2006
  • Process Moisture Analysis using FT-NIR

    Manufacturing a pure product can be critically important to the next steps in the manufacture of a powder-based product. As a result the removal of residual moisture and solvents from the crystallization, filtration and drying steps can be crucial to producing a stable product.

    Bruker Optics
    06/28/2006
1-20 of 24 < first | prev | | last >