Perspectives: Process Puzzler

Get Relief From Valve Popping

Readers suggest ways to address thermal expansion issue.

*THIS MONTH’S PUZZLER* We’re suffering an annoying thermal expansion problem in the ethylene oxide (EO) lines that feed our reactors: pressure relief valves (PRVs) often pop from solar heating, because lines are blocked in, typically for up to ten minutes. (Our design standard assumes horizontal pipe and a maximum ambient temperature of 95°F, which doesn’t occur very often at our Chicago site: solar flux is 38.7 Btu/h-ft2 for the summer solstice.) The PRVs wouldn’t be such a problem but EO can polymerize and cause them to stick open, which is why the covered area under the reactors is Class 1, Division 1, Group B. The EO feed pipe runs at 55 psig at 60°F. The PRVs are set at 145 psig. Barometric pressure is 14.408 psia. The properties of EO at operating conditions are: density, 66.8 lb/ft3; viscosity, 0.302 cP; heat capacity, 0.476 BTU/lb-F; thermal conductivity, 0.0949 BTU/h-ft2-°R; volumetric thermal expansion coefficient, 0.001°F-1; and bulk modulus, 180,000 psi/ft3. Our plant engineer is convinced that two inches of calcium silicate insulation in a stainless steel jacket over our 1½-in. Schedule-80 Type-316 stainless-steel pipe largely will eliminate our PRV reliability problem. What do you think?

Read more

More from this perspective...

Title

Process Puzzler: Serve up better column operation

Readers tackle Chemical Processing's process puzzler question and offer tips about how to keep a stripper column from flooding.

12/21/2004

Process Puzzler: Keep cables in their place

A Chemical Processing reader was looking for a solution to a cable hanger problem. At his plant, a 200-lb. cable bundle supported by cable hangers fell and injured one man. Read what advice our readers had for him and take a look at next months' question.

02/21/2005

Process Manufacturing Puzzler: Stop solvent losses

A reader is sufferring significant solvent losses during his batch process. Read about how his peers might solve his problem.

04/01/2005

Process Puzzler: Choose a pump wisely

Readers offer tips about how to choose the best pump for slurry service.

05/25/2005

Cure column hiccups

12/29/2005

Prevent heat-exchanger plugging

Readers suggest how to keep a solvent recovery system running smoothly.

12/30/2005

Don’t waste your boilers

Chemical Processing's readers offer tips about how to properly isolate a waste heat boiler.

01/02/2006

Track that spill

Chemical Processing's readers offer tips about how to locate and identify a chemical spill.

01/02/2006

Know when the end is near

Chemical Processing's readers offer tips about how to determine resin-reaction end point.

01/02/2006

Condensate cripples compressor

Readers offer tips on how to keep a standby compressor ready for service.

01/05/2006

Making sense of temperature sensing

Readers provide solutions to a thermowell problem in this month's Process Puzzler.

01/06/2006

April 2006 Process Puzzler: Fixing a Fouled Flue Gas System

Readers identify the cause of poor absorption in flue gas system in this month's process puzzler.

03/11/2006

May Process Puzzler: Boost the reliability of a solvent supply pump

Readers suggest solutions to cavitation in this month's Process Puzzler.

05/25/2006

July Process Puzzler: Prevent the burn-out of a mixer

Readers suggest quick solutions to a solid-liquid mixing problem in Chemical Processing's monthly Process Puzzler feature.

06/28/2006

August Process Puzzler: Avoiding a future accident

Readers suggest possible causes for a mysterious mixer explosion in Chemical Processing's monthly Process Puzzler feature.

08/22/2006

September Process Puzzler: Uncovering cause of solid build-up

Readers offer suggestions to improve reliability of a vibrating screen in Chemical Processing's monthly Process Puzzler feature.

09/14/2006

October Process Puzzler: Improve centrifuge separation capacity, quality

Readers offer suggestions to improve centrifuge separation capacity and quality in Chemical Processing's monthly Process Puzzler feature.

09/29/2006

November Process Puzzler: Consider options for automation

Readers suggest ways to automate an HCl absorber in this month's Process Puzzler in Chemical Processing.

10/31/2006

December Process Puzzler: Debug a weigh feeder

Readers offer ideas for improving reliability of a weigh feeder in Chemical Processing's monthly Process Puzzler feature.

11/29/2006

January Process Puzzler: Sticky valve

Readers offer ideas for the cause of a sticky valve in Chemical Processing's monthly Process Puzzler feature.

01/03/2007