Perspectives: Energy Saver

Are you getting the most from your exchange?

Use a pinch study to gain better understanding of your heating and cooling sources.

By Gary Faagau, energy columnist

Related articles

Heat Transfer Research forms heat exchanger design task force

Reviewing the use of fouling factors in heat exchanger design

Achieve effective heat exchanger control

Heat recovery is vital to good plant efficiency, but rarely tackled. The reason is simple. If your system doesn’t have the proper configuration to efficiently recover heat, then operationally all you can do is clean (keep your heat transfer surface free of dirt, sludge, scale and other deposits)what you have. But, chances are your feeds and products have varied from the original design. Also, the design was probably created when energy prices were low. If you’ve pushed your unit and are running against cooling or heating limits, it’s time to sit down and rethink your heat integration.

Take a survey of all the streams on your unit before they’re either heated or cooled. With these data,  perform a pinch analysis of the entire unit.  Pinch Technology isn’t that difficult and software is available to make the analysis easier. However, you have to purchase and learn the software as well as become a pinch expert to really get full value. Unless you’re planning to go into this line of work, it may be easier to send the study to a company that can do the analysis for you. But how do you justify the expense when you don’t know if there will be a positive result?

Before  spending the money, do a simplified pinch study at your desk. Pinch is all about using heating sources in the proper location. List all the streams that need to be heated on your unit in one column of a worksheet and then sort them by the final temperature they need to reach. In a different column, list all the streams that need to be cooled, sorting them by initial temperature from lowest to highest. Streams that need to be cooled include anything that exchanges with cooling water, fin fan, or is exhausted to air at elevated temperatures, like flue gas or vent steam.

In a third column, list available utility heat, including various steam pressures, fired heating, and cost. Using an exchanger simulation program, like HYSYS or PRO II, get your average heat capacity over the range needed to heat or cool your streams. Using just the worksheet with the rates, heat capacities and temperatures, configure your current heating system. This helps check to see if you have the correct information.

Next,  work on redesign. Start heating your most important streams, using available streams that need to be cooled. For a normal shell-and-tube exchanger, a 20ºF approach is a reasonable assumption. If the stream being cooled is large enough, consider a more elaborate set of exchangers and use a 15ºF or 10ºF approach. If there are a lot of different choices, start making logical decisions based on plant layout, current exchange medium, or what does the job simplest. Using a  spreadsheet for the task is simpler and allows you to better visualize what needs to be done.

Take into account that some streams need to be cooled to storage temperature and others require only a set temperature drop. Sometimes you may need a stream to provide heat at a high temperature and then  at a cooler temperature. Just split the stream by temperature, making sure to interlock the hotter stream’s outlet temperature after the hot exchange to the inlet of the cooler stream. Try not to use a very hot stream to do low temperature heating. Don’t forget to use waste heat streams.

Once you have heated your stream as much as you can with process streams, finish the job with utility streams. Remember it may be possible to put a low-cost utility stream in the middle of your system instead of a higher cost utility stream at the upper end.

Although  your worksheet may need to be changed several times, it’s much easier for a novice programmer to switch a few cells on a spreadsheet then to redo connections in a simulation program. Once you have the worksheet completed, calculate potential savings. If it looks like it may be worthwhile to go with a design change, then simulate your new design to verify your calculations.

This method isn’t foolproof as you may miss a big opportunity, but if you can find a better cost effective design, you can be assured that it wouldn’t be a waste of money to start a heat integration study project. This may take some thinking, but working with a spreadsheet gives you a better understanding of your heating and cooling sources and saves a lot of time in running simulation models.

More from this perspective...

Title

Innovations Promise Better Energy Efficiency

Five developing technologies may profoundly impact plant practices.

03/09/2010

Innovative Fixes for Saving Energy in Plants

Some uncommon practices can help reduce plant costs

08/07/2008

It’s Time to Answer The E(nergy)-Mail

Readers provide their input on content of recent columns.

09/03/2009

It’s Time to Review Your Plant Energy Systems

Annual checkups help ensure components keep running smoothly.

01/16/2009

It’s time for a design check

Pay closer attention to energy efficiency and impose standards.

02/13/2008

Know the Basics of Energy Management

Make energy management maintenance a routine part of your day.

11/22/2010

Make Your Energy Savings Permanent

Here are five ways to create sustainable energy programs.

10/14/2008

Make the Case for Energy Improvements, II

Implementing two near-term measures saves a petrochemical plant millions

03/13/2013

Make the Case for Energy Improvements, III

Waste heat can provide cooling via ammonia absorption refrigeration.

04/10/2013

Make the Case for Energy Improvements, Part I

An ammonia plant saves millions annually with a few medium-term measures.

02/07/2013

Manage Your Energy Management Program

Learn what roles make up a successful energy management program.

07/31/2012

New Energy Efficiency Standards Are Coming

Government, industry and academia team up on program.

01/13/2010

Not All Carbon Dioxide Is Created Equal

Put biomass to use to help reduce your plant’s carbon footprint.

07/07/2009

Optimize Boiler Loads

A boiler's limited turndown ratio causes huge dollar losses.

10/16/2013

Optimize Electrical Systems, Part I

Many facilities can reduce costs by performing simple operations

08/26/2014

Optimize Electrical Systems, Part II

Take a closer look at electric motors and plugged-in loads for potential energy savings.

09/29/2014

Optimize Energy Costs in Petroleum Refineries, Part I

Improve refining margins with more energy efficient measures.

02/21/2012

Optimize Energy Costs in Refineries, Part II

Several options can improve condensate recovery.

03/20/2012

Optimize Energy Costs, Part I

Several petrochemical examples highlight energy efficiency.

12/20/2011

Optimize Energy Costs, Part II

Alternative process heating methods could offer attractive pay-offs.

01/25/2012