Articles

301-320 of 386 < first | | | last >
  • Best practices in control system migration

    Migration from your old control system to a new one is as an inevitable as death and taxes. But, the key to minimizing the pain is to abide by the control system migration best practices listed here.

    Dan Hebert, PE, Senior Technical Editor
    02/09/2007
  • 10 tips for diagnosing control valve problems

    To make the most of diagnostic equipment used in chemical processing, technicians must stretch their knowledge of control valves and related diagnostic equipment that keeps tabs on valve health and safety.

    David W. Douglas
    01/22/2007
  • Exporters get reporting relief

    EPA eases annual reporting requirements and thresholds, and exporters are feeling relief, according to Lynn Bergeson in her monthly Compliance Advisor column.

    Lynn Bergeson, regulatory editor
    01/08/2007
  • pH sensor stands up to tough conditions

    Design provides improved reliability in a polymer-precursor batch reactor. Sensors must respond quickly and survive a harsh environment. Poor probe reliability can make the difference between a process that makes money and one that doesn’t.

    Kyle Becker, Polychemie
    01/08/2007
  • Distillation control and optimization, Part 3

    Control's Béla Lipták continues his series on control of distillation processes, this time focusing on managing reboiler flow, temperature, feed rate, loading and reflux for economy, stability and safety.

    Béla Lipták, PE, CONTROL Columnist
    01/05/2007
  • How to select control valves, Part 3

    When it comes to selecting and sizing control valves, gain and stability are key characteristics. The non-commercial valve selection chart in this article serves as a reference tool you can download.

    Béla Lipták, Contributing Writer
    12/19/2006
  • Keep measurements on the level

    This article looks at six technologies — mechanical floats and displacers, differential pressure, capacitance, ultrasonic, radar, and guided wave radar — that are used most often for automated control, and provides practical guidance for choosing among them.

    Jerry Boisvert, Siemens Energy & Automation
    11/01/2006
  • Choosing motor controls and drives

    In any industrial control application, using the right drives and motor controls can make or break the project, and also can make a huge difference in how well those applications perform.

    10/18/2006
  • How to select control valves, Part 2

    When it comes to selecting and sizing control valves and positioners, this article not only helps you pick the right one for the right job, but also includes a valuable valve selection chart you can download!

    Béla Lipták, PE, CONTROL Columnist
    10/17/2006
  • Raising the bar for control system security

    Security researchers at Wurldtech Analytics are partnering with ISA to establish procedures and an operations model for the security testing and certification of products used for control.

    Eric and Joann Byres, principals, Wurldtech Analytics
    10/12/2006
  • Boiling water is easy as one, two, three, four

    There’s more to boiler level control than measuring level and adjusting a feedwater valve. Improved measurements and inverse response are just a few of the influences on operating boilers in a reliable manner.

    David W. Spitzer
    09/15/2006
  • Heat integration steps can present control problems

    The more energy prices rise, the more heat integration saves. However, heat integration steps can present complex control problems. Slip-ups in putting control systems in place can make operations nearly impossible. That certainly was the case at one unit using heat recovery.

    Andrew Sloley, contributing editor and Carolyn K. Hawley, VECO USA
    09/13/2006
  • Fieldbus improves control system reliability

    Profibus-PA and Foundation Fieldbus both reduce cabling cost by sharing wiring among several field instruments. They also save money by reducing the number of instrument interface cards required to connect field instruments to the control system. However, they all save money by being able to use the same field transmitter for a wide range of measured variables.

    Dick Caro
    09/11/2006
  • The rise and fall of modulation

    Why have reciprocating designs fallen out of favor relative to the rotary compressor that is so predominant today? Read about the evolution of efficient controls for compressed air systems.

    Henry Kemp
    09/11/2006
  • HMIs evolve in process control

    New HMI technology is putting a whole new (inter)face on how operators view control systems information, while at the same time driving human error out of systems and improving safe work practices.

    Ian Nimmo, president, User Centered Design Services LLC
    09/11/2006
  • Innovations in batching, dosing and weighing

    Challenges brought on by new regulations and technical problems for batching, dosing and weighing have pushed users to find some innovative and surprising solutions beyond our own industry.

    09/05/2006
  • How to select control valves, Part 1

    When it comes to selecting and sizing control valves, the non-commercial chart in this article not only helps you pick the right one for the job, but also serves as a reference tool you can download.

    Béla Lipták, PE, CONTROL Columnist
    08/15/2006
  • Try before you buy

    There is another side to toll processing. It involves the companies that arguably have the best possible know-how and hardware — for the simple reason that they are the equipment manufacturers themselves, offering toll processing services that utilize their own products.

    Mike Spear, editor at large
    07/24/2006
  • Control your maintenance

    Automation systems have now reached such a high degree of reliability that many personnel at plants now take them for granted. Learn to use digital communication with your asset management tools to achieve predictive maintenance and substantial savings.

    Ian Verhappen, MTL Instruments Group
    07/12/2006
301-320 of 386 < first | | | last >