281-300 of 385 < first | | | last >
  • The evolution of plant automation

    Understanding the purpose of control and safety systems helps users ensure each is appropriately optimized. The duties of the SIS are to protect the people, environment and assets against unsafe conditions.

    Angela Summers, PhD, PE, founder of SIS-TECH Solutions
  • Pressure control optimization

    Floating pressure control means that, at minimum pressure, the heat required at the reboiler is minimized, its capacity is increased, and fouling is reduced.

    Béla Lipták, PE, CONTROL Columnist
  • Take the pressure off pressure control

    Linkage of other variables can stymie hot vapor bypass schemes, according to Andrew Sloley's Plant InSites column.

    Andrew Sloley, contributing editor
  • Chemical security rules edge forward

    Advance rulemaking was recently issued on anti-terrorism standards. Lynn Bergeson provides a summary in monthly Compliance Advisor column.

    Lynn Bergeson, regulatory editor
  • The DCS spirit lives on everywhere

    Classic distributed control systems typically remain only in high-availability refining and power applications, but their strategies and capabilities persist in descendants and today’s sophisticated networks.

    Jim Montague, Executive Editor
  • Best practices in control system migration

    Migration from your old control system to a new one is as an inevitable as death and taxes. But, the key to minimizing the pain is to abide by the control system migration best practices listed here.

    Dan Hebert, PE, Senior Technical Editor
  • 10 tips for diagnosing control valve problems

    To make the most of diagnostic equipment used in chemical processing, technicians must stretch their knowledge of control valves and related diagnostic equipment that keeps tabs on valve health and safety.

    David W. Douglas
  • Exporters get reporting relief

    EPA eases annual reporting requirements and thresholds, and exporters are feeling relief, according to Lynn Bergeson in her monthly Compliance Advisor column.

    Lynn Bergeson, regulatory editor
  • pH sensor stands up to tough conditions

    Design provides improved reliability in a polymer-precursor batch reactor. Sensors must respond quickly and survive a harsh environment. Poor probe reliability can make the difference between a process that makes money and one that doesn’t.

    Kyle Becker, Polychemie
  • Distillation control and optimization, Part 3

    Control's Béla Lipták continues his series on control of distillation processes, this time focusing on managing reboiler flow, temperature, feed rate, loading and reflux for economy, stability and safety.

    Béla Lipták, PE, CONTROL Columnist
  • How to select control valves, Part 3

    When it comes to selecting and sizing control valves, gain and stability are key characteristics. The non-commercial valve selection chart in this article serves as a reference tool you can download.

    Béla Lipták, Contributing Writer
  • Keep measurements on the level

    This article looks at six technologies — mechanical floats and displacers, differential pressure, capacitance, ultrasonic, radar, and guided wave radar — that are used most often for automated control, and provides practical guidance for choosing among them.

    Jerry Boisvert, Siemens Energy & Automation
  • Choosing motor controls and drives

    In any industrial control application, using the right drives and motor controls can make or break the project, and also can make a huge difference in how well those applications perform.

  • How to select control valves, Part 2

    When it comes to selecting and sizing control valves and positioners, this article not only helps you pick the right one for the right job, but also includes a valuable valve selection chart you can download!

    Béla Lipták, PE, CONTROL Columnist
  • Welcome to the Bus Wars, Part Tres

    You may not be aware, but a new bus war is being waged in your plant — the battle of the motion networks. Control Global's Senior Tech Editor Dan Hebert, PE, provides analysis and commentary on the newest battle over fieldbus.

    Dan Hebert, PE, Senior Technical Editor
  • Raising the bar for control system security

    Security researchers at Wurldtech Analytics are partnering with ISA to establish procedures and an operations model for the security testing and certification of products used for control.

    Eric and Joann Byres, principals, Wurldtech Analytics
  • Washington targets plant security

    Federal actions undoubtedly will markedly impact the chemical industry. Nevertheless, we don’t know at this point whether federal chemical security legislation will happen in 2006.

    David A. Moore and Dorothy Kellogg, AcuTech Consulting Group
  • Security poses an inherent industry dilemma

    Industry faces the threat of draconian demands from Congress as chemical plants remain an attractive targets for terrorism attacks, according to Mark Rosenzweig, editor in chief of Chemical Processing.

    Mark Rosenzweig, editor in chief
  • Boiling water is easy as one, two, three, four

    There’s more to boiler level control than measuring level and adjusting a feedwater valve. Improved measurements and inverse response are just a few of the influences on operating boilers in a reliable manner.

    David W. Spitzer
  • Heat integration steps can present control problems

    The more energy prices rise, the more heat integration saves. However, heat integration steps can present complex control problems. Slip-ups in putting control systems in place can make operations nearly impossible. That certainly was the case at one unit using heat recovery.

    Andrew Sloley, contributing editor and Carolyn K. Hawley, VECO USA
281-300 of 385 < first | | | last >