241-260 of 332 < first | | | last >
  • Distillation control and optimization, Part 3

    Control's Béla Lipták continues his series on control of distillation processes, this time focusing on managing reboiler flow, temperature, feed rate, loading and reflux for economy, stability and safety.

    Béla Lipták, PE, CONTROL Columnist
  • How to select control valves, Part 3

    When it comes to selecting and sizing control valves, gain and stability are key characteristics. The non-commercial valve selection chart in this article serves as a reference tool you can download.

    Béla Lipták, Contributing Writer
  • Data validation: Jewel in the fieldbus crown?

    Many users and most suppliers to the industry see process availability as the big payout benefit of Foundation Fieldbus (FF) diagnostics — a good portion of it realized through data validation.

    John Rezabek, Contributing Editor
  • Keep measurements on the level

    This article looks at six technologies — mechanical floats and displacers, differential pressure, capacitance, ultrasonic, radar, and guided wave radar — that are used most often for automated control, and provides practical guidance for choosing among them.

    Jerry Boisvert, Siemens Energy & Automation
  • Choosing motor controls and drives

    In any industrial control application, using the right drives and motor controls can make or break the project, and also can make a huge difference in how well those applications perform.

  • How to select control valves, Part 2

    When it comes to selecting and sizing control valves and positioners, this article not only helps you pick the right one for the right job, but also includes a valuable valve selection chart you can download!

    Béla Lipták, PE, CONTROL Columnist
  • Welcome to the Bus Wars, Part Tres

    You may not be aware, but a new bus war is being waged in your plant — the battle of the motion networks. Control Global's Senior Tech Editor Dan Hebert, PE, provides analysis and commentary on the newest battle over fieldbus.

    Dan Hebert, PE, Senior Technical Editor
  • Raising the bar for control system security

    Security researchers at Wurldtech Analytics are partnering with ISA to establish procedures and an operations model for the security testing and certification of products used for control.

    Eric and Joann Byres, principals, Wurldtech Analytics
  • Boiling water is easy as one, two, three, four

    There’s more to boiler level control than measuring level and adjusting a feedwater valve. Improved measurements and inverse response are just a few of the influences on operating boilers in a reliable manner.

    David W. Spitzer
  • Heat integration steps can present control problems

    The more energy prices rise, the more heat integration saves. However, heat integration steps can present complex control problems. Slip-ups in putting control systems in place can make operations nearly impossible. That certainly was the case at one unit using heat recovery.

    Andrew Sloley, contributing editor and Carolyn K. Hawley, VECO USA
  • Fieldbus improves control system reliability

    Profibus-PA and Foundation Fieldbus both reduce cabling cost by sharing wiring among several field instruments. They also save money by reducing the number of instrument interface cards required to connect field instruments to the control system. However, they all save money by being able to use the same field transmitter for a wide range of measured variables.

    Dick Caro
  • The rise and fall of modulation

    Why have reciprocating designs fallen out of favor relative to the rotary compressor that is so predominant today? Read about the evolution of efficient controls for compressed air systems.

    Henry Kemp
  • Process analysis gains greater online role

    Faster. Smaller. Smarter. Modular. All express the future of process analytics. And un-stoppable describes the ongoing migration of process analytical instruments to continuous, online, field-mounted use at chemical plants.

    C. Kenna Amos, contributing editor
  • HMIs evolve in process control

    New HMI technology is putting a whole new (inter)face on how operators view control systems information, while at the same time driving human error out of systems and improving safe work practices.

    Ian Nimmo, president, User Centered Design Services LLC
  • Innovations in batching, dosing and weighing

    Challenges brought on by new regulations and technical problems for batching, dosing and weighing have pushed users to find some innovative and surprising solutions beyond our own industry.

  • Fieldbus wars continue

    As wireless Ethernet continues its aggressive growth, end users have to wonder, “Will it replace fieldbuses?” It is clear that a battle is shaping up.

    Rich Merritt, senior technical editor
  • How to select control valves, Part 1

    When it comes to selecting and sizing control valves, the non-commercial chart in this article not only helps you pick the right one for the job, but also serves as a reference tool you can download.

    Béla Lipták, PE, CONTROL Columnist
  • Cutting the wires of communications

    Users want wireless, vendors want to sell wireless, so what’s the problem? This article tackles one of the most discussed topics: the use of wireless communications in process automation.

    Walt Boyes, Editor in Chief
  • Try before you buy

    There is another side to toll processing. It involves the companies that arguably have the best possible know-how and hardware — for the simple reason that they are the equipment manufacturers themselves, offering toll processing services that utilize their own products.

    Mike Spear, editor at large
241-260 of 332 < first | | | last >