Articles

181-200 of 242 < first | | | last >
  • Avoid trouble with slurries

    Handling slurries (a mix of solids and liquids), should be based on experience and experiments, not theory. Much of the knowledge obtained from pneumatic conveyors and fluidization systems can be used in understanding slurries.

    Thomas R. Blackwood, Healthsite Associates
    11/01/2006
  • Choosing motor controls and drives

    In any industrial control application, using the right drives and motor controls can make or break the project, and also can make a huge difference in how well those applications perform.

    10/18/2006
  • How to select control valves, Part 2

    When it comes to selecting and sizing control valves and positioners, this article not only helps you pick the right one for the right job, but also includes a valuable valve selection chart you can download!

    Béla Lipták, PE, CONTROL Columnist
    10/17/2006
  • The FRETT approach to pump problems

    Some U.S. oil refineries repair their centrifugal pumps every three years while other refineries enjoy an average repair interval of 10 years. Learn about the highest-performing refineries and other petrochemical companies that have significantly reduced pump failures, and how you can obtain the same results.

    Heinz P. Bloch, P.E.
    10/16/2006
  • Increase pump performance

    In this web exclusive on ChemicalProcessing.com, pump expert Ross Mackay says a key to a pump's performance is to look at the control system it's running with.

    Ross Mackay
    09/18/2006
  • Remember the old reliable orifice plate

    The cost-effective dP flow meter is ideal for utility surveys, Senior Editor Dirk Willard says in this month's Chemical Processing Field Notes column.

    Dirk Willard, senior editor
    09/11/2006
  • Keep a steady eye on measurements

    While engineers often strive to keep processes running without too much variation, measurements that don’t change may be a cause for concern not celebration, as one refinery can attest.

    Andrew Sloley, contributing editor
    06/19/2006
  • Pumping Temperature Considerations

    "Bad actor" pumps are those pumps that have trouble with frequent and repetitive failures. In many cases, the source of the problem is an ANSI pump trying valiantly to handle a liquid well beyond the range of its design rating.of 300 degs. F.

    Ross Mackay
    06/19/2006
  • Get a handle on solids’ flow

    Properly accounting for how bulk solids actually will flow in a vessel or overall process can be crucial for successful operations. Learning some simple parameters can often provide a good sense of flowability.

    Don McGlinchey, Glasgow Caledonian University
    05/22/2006
  • Flow metering gets more fluid

    There are more and more funcationalities being added to your most trusted instrumentation. These established technologies have expand their reach and performance.

    Mike Spear, editor at large
    01/09/2006
  • Pumps benefit from a vane effort

    Widely used but underappreciated, back pump-out vanes extend bearings and seal life.

    Richard Nardone, ITT Industrial & BioPharm Group
    11/15/2005
  • pH linearization lubricates waste control

    Learn how a simplified technique for linearizing pH can enhance control in waste treatment applications and eliminate the need for gain-adjusting techniques.

    11/15/2005
  • Find the best value seal

    A new industry-developed tool provides insights and practical guidance on seal economics.

    Pete Petrunich
    10/18/2005
  • Flow Meter Focus

    ChemicalProcessing.com introduces Flow meter focus, a compilation of useful articles, news, white papers and product information related to flow meters.

    09/28/2005
  • Make the most of HART-enabled field devices

    HART-enabled field devices offer many benefits and not just for process control. They can lead to productivity gains, maintenance savings and more efficient and accurate recordkeeping.

    Dan Prugar, Meriam Process Technologies
    08/11/2005
  • Software Drives OEM Toward Efficiency and Energy Savings

    ABB designed software for its ACS800 drive so Curtis-Toledo could improve the operation of its rotary-screw compressors. The customized software can control the system pressure, air delivery, oil temperature and duty cycle directly from the drive.

    John Wilmes, ABB Inc.
    06/23/2005
181-200 of 242 < first | | | last >