Articles

1001-1020 of 1222 < first | | | last >
  • Make your portable mixer work for you

    Understanding the fundamentals of fluid agitation can help meet the customer’s requirement and the processor’s need for efficiency. While portable mixers have been around for years, they often aren’t used to their full potential. Knowing the basics of mixing and flow patterns can help you get more out of your mixer.

    David Dickey, MixTech, Inc. and Lydia Booth Fenley, Illes Seasonings & Flavors
    03/06/2007
  • Still pondering whither fieldbus?

    In this month's installment of On the Bus, Contributing Editor John Rezabek predicts HART devices will work so well that your career may be over before you can justify the cost to replace them with fieldbus.

    John Rezabek, Contributing Editor
    03/03/2007
  • NeSSI taxis for takeoff

    Though acceptance and networking hurdles remain, the New Sampling/Sensor Initiative (NeSSI) is starting to emerge in real-world, standardized, modular process control applications.

    Jim Montague, Executive Editor
    03/03/2007
  • The evolution of plant automation

    Understanding the purpose of control and safety systems helps users ensure each is appropriately optimized. The duties of the SIS are to protect the people, environment and assets against unsafe conditions.

    Angela Summers, PhD, PE, founder of SIS-TECH Solutions
    03/03/2007
  • Pressure control optimization

    Floating pressure control means that, at minimum pressure, the heat required at the reboiler is minimized, its capacity is increased, and fouling is reduced.

    Béla Lipták, PE, CONTROL Columnist
    03/03/2007
  • Remember the basics of maintenance

    Despite the “buzz” about asset management systems don’t forget the “oilers”, advises Mike Spear, in this month's End Point column.

    Mike Spear, editor at large
    03/01/2007
  • Plants get help in boosting reliability

    More and more companies are placing greater emphasis on maintenance and seeking help from vendors to boost the effectiveness of their efforts, as some recent major investment decisions demonstrate. Many automation companies now are benefiting by building up asset management services alongside process control capabilities.

    Mike Spear, editor at large
    02/26/2007
  • Take the pressure off pressure control

    Linkage of other variables can stymie hot vapor bypass schemes, according to Andrew Sloley's Plant InSites column.

    Andrew Sloley, contributing editor
    02/19/2007
  • Chemical security rules edge forward

    Advance rulemaking was recently issued on anti-terrorism standards. Lynn Bergeson provides a summary in monthly Compliance Advisor column.

    Lynn Bergeson, regulatory editor
    02/12/2007
  • The DCS spirit lives on everywhere

    Classic distributed control systems typically remain only in high-availability refining and power applications, but their strategies and capabilities persist in descendants and today’s sophisticated networks.

    Jim Montague, Executive Editor
    02/09/2007
  • Best practices in control system migration

    Migration from your old control system to a new one is as an inevitable as death and taxes. But, the key to minimizing the pain is to abide by the control system migration best practices listed here.

    Dan Hebert, PE, Senior Technical Editor
    02/09/2007
  • Debunk plant myths about diagnostics

    Your current control system can probably do more than you think. Everybody can agree that diagnostics are a good thing — they can identify problems early, and keep the plant running at peak performance. Learn how your existing control systems and analog instruments can deliver diagnostic capabilities, at a fraction of the cost of system or instrument replacements.

    George Buckbee, ExperTune, Inc.
    02/08/2007
  • Making the most of diagnostics

    Make the most of your diagnostics with this helpul summary from George Buckbee of ExperTune, Inc.

    George Buckbee, ExperTune, Inc.
    02/08/2007
  • Energy Savings Pick up Steam

    More attention to steam systems and trap monitoring provides big benefits. At most chemical plants, plant management and operators face increasing pressures to improve the energy efficiency of their processes, so they should see how they can save on steam.

    Mike Spear, editor at large
    01/30/2007
  • 10 tips for diagnosing control valve problems

    To make the most of diagnostic equipment used in chemical processing, technicians must stretch their knowledge of control valves and related diagnostic equipment that keeps tabs on valve health and safety.

    David W. Douglas
    01/22/2007
  • Where is wireless going?

    Increasing interest will translate into far more monitoring applications. The worldwide market for wireless technology will grow 26% annually over the next few years, forecasts the ARC Advisory Group. Vendors are responding and key concerns are being addressed.

    Mike Spear, editor at large
    01/11/2007
  • Exporters get reporting relief

    EPA eases annual reporting requirements and thresholds, and exporters are feeling relief, according to Lynn Bergeson in her monthly Compliance Advisor column.

    Lynn Bergeson, regulatory editor
    01/08/2007
  • pH sensor stands up to tough conditions

    Design provides improved reliability in a polymer-precursor batch reactor. Sensors must respond quickly and survive a harsh environment. Poor probe reliability can make the difference between a process that makes money and one that doesn’t.

    Kyle Becker, Polychemie
    01/08/2007
  • Distillation control and optimization, Part 3

    Control's Béla Lipták continues his series on control of distillation processes, this time focusing on managing reboiler flow, temperature, feed rate, loading and reflux for economy, stability and safety.

    Béla Lipták, PE, CONTROL Columnist
    01/05/2007
1001-1020 of 1222 < first | | | last >