Articles

361-380 of 467 < first | | | last >
  • Sample pump eliminates emissions

    A compact system significantly improves analyzer accuracy. This innovative turnkey solution for analyzer emissions is a solid-state pump with an ultra-sensitive pressure regulator that mixes a compatible gas with the analyzer samples to achieve a constant vent header pressure — even during times of plant upset.

    Kazi Hassa, Parker Hannifin
    03/20/2007
  • Chemical industry sees green

    Developments target economics, not just environmental benefits. While pollution prevention was the original goal of green chemistry, today’s efforts promise to have a substantial economic impact.

    Mike Spear, editor at large
    01/03/2007
  • Flowmeters clean and dirty

    ControlGlobal.com contributor David W. Spitzer provides a look from a process automation perspective at how magmeters and Venturi meters are vying with ultrasonics for clean and dirty water applications.

    David W. Spitzer
    11/09/2006
  • Avoid trouble with slurries

    Handling slurries (a mix of solids and liquids), should be based on experience and experiments, not theory. Much of the knowledge obtained from pneumatic conveyors and fluidization systems can be used in understanding slurries.

    Thomas R. Blackwood, Healthsite Associates
    11/01/2006
  • Get answers to your biomonitoring questions

    Guidance for chemical manufacturers, processors, and distributors about Section 8(e) of the Toxic Substances control act was issued on September 14, by the U.S. Environmental Protection Agency (EPA). Chemical Processing's Regulatory Editor Lynn Bergeson discusses the new regulation.

    Lynn Bergeson, regulatory editor
    10/24/2006
  • Choosing motor controls and drives

    In any industrial control application, using the right drives and motor controls can make or break the project, and also can make a huge difference in how well those applications perform.

    10/18/2006
  • How to select control valves, Part 2

    When it comes to selecting and sizing control valves and positioners, this article not only helps you pick the right one for the right job, but also includes a valuable valve selection chart you can download!

    Béla Lipták, PE, CONTROL Columnist
    10/17/2006
  • The FRETT approach to pump problems

    Some U.S. oil refineries repair their centrifugal pumps every three years while other refineries enjoy an average repair interval of 10 years. Learn about the highest-performing refineries and other petrochemical companies that have significantly reduced pump failures, and how you can obtain the same results.

    Heinz P. Bloch, P.E.
    10/16/2006
  • Washington targets plant security

    Federal actions undoubtedly will markedly impact the chemical industry. Nevertheless, we don’t know at this point whether federal chemical security legislation will happen in 2006.

    David A. Moore and Dorothy Kellogg, AcuTech Consulting Group
    09/22/2006
  • Increase pump performance

    In this web exclusive on ChemicalProcessing.com, pump expert Ross Mackay says a key to a pump's performance is to look at the control system it's running with.

    Ross Mackay
    09/18/2006
  • Succeed at bioprocess scale-up

    While fermentation-based syntheses were once reserved for producing high-value specialty chemicals and biopharmaceuticals, bioprocess routes now are gaining increasing attention for commodity products.

    John L. Shaw, P.E., and Scott A. Rogers, P.E., CH2MHill Lockwood Greene
    08/28/2006
  • The impact of the European Union's directives on the U.S.

    The Restrictions of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment (the RoHS Directive) is part of a growing wave of European Union product-based regulations that will profoundly impact global and United States product standards — and thus the chemical industry.

    Lynn Bergeson, regulatory editor
    08/17/2006
  • Pump Performance: Kayo Cavitation

    Checking pump performance curves is one of the first steps in troubleshooting a centrifugal pump problem or seeing if a pump can handle new service conditions. Learn to look for more than just insufficient NPSHA, the common culprit, when investigating cavitation.

    Andrew Sloley, contributing editor
    07/17/2006
  • Small sensors promise big impact

    Because many environmental applications of nanotechnology will almost certainly revolutionize the science, law, and regulation of water pollution, readers are urged to keep abreast of this fast-changing area.

    Lynn Bergeson, regulatory editor
    06/28/2006
  • Keep a steady eye on measurements

    While engineers often strive to keep processes running without too much variation, measurements that don’t change may be a cause for concern not celebration, as one refinery can attest.

    Andrew Sloley, contributing editor
    06/19/2006
  • Pumping Temperature Considerations

    "Bad actor" pumps are those pumps that have trouble with frequent and repetitive failures. In many cases, the source of the problem is an ANSI pump trying valiantly to handle a liquid well beyond the range of its design rating.of 300 degs. F.

    Ross Mackay
    06/19/2006
361-380 of 467 < first | | | last >