Articles

341-360 of 456 < first | | | last >
  • Data validation: Jewel in the fieldbus crown?

    Many users and most suppliers to the industry see process availability as the big payout benefit of Foundation Fieldbus (FF) diagnostics — a good portion of it realized through data validation.

    John Rezabek, Contributing Editor
    11/09/2006
  • Avoid trouble with slurries

    Handling slurries (a mix of solids and liquids), should be based on experience and experiments, not theory. Much of the knowledge obtained from pneumatic conveyors and fluidization systems can be used in understanding slurries.

    Thomas R. Blackwood, Healthsite Associates
    11/01/2006
  • Keep measurements on the level

    This article looks at six technologies — mechanical floats and displacers, differential pressure, capacitance, ultrasonic, radar, and guided wave radar — that are used most often for automated control, and provides practical guidance for choosing among them.

    Jerry Boisvert, Siemens Energy & Automation
    11/01/2006
  • Choosing motor controls and drives

    In any industrial control application, using the right drives and motor controls can make or break the project, and also can make a huge difference in how well those applications perform.

    10/18/2006
  • How to select control valves, Part 2

    When it comes to selecting and sizing control valves and positioners, this article not only helps you pick the right one for the right job, but also includes a valuable valve selection chart you can download!

    Béla Lipták, PE, CONTROL Columnist
    10/17/2006
  • The FRETT approach to pump problems

    Some U.S. oil refineries repair their centrifugal pumps every three years while other refineries enjoy an average repair interval of 10 years. Learn about the highest-performing refineries and other petrochemical companies that have significantly reduced pump failures, and how you can obtain the same results.

    Heinz P. Bloch, P.E.
    10/16/2006
  • Increase pump performance

    In this web exclusive on ChemicalProcessing.com, pump expert Ross Mackay says a key to a pump's performance is to look at the control system it's running with.

    Ross Mackay
    09/18/2006
  • Process analysis gains greater online role

    Faster. Smaller. Smarter. Modular. All express the future of process analytics. And un-stoppable describes the ongoing migration of process analytical instruments to continuous, online, field-mounted use at chemical plants.

    C. Kenna Amos, contributing editor
    09/11/2006
  • Cutting the wires of communications

    Users want wireless, vendors want to sell wireless, so what’s the problem? This article tackles one of the most discussed topics: the use of wireless communications in process automation.

    Walt Boyes, Editor in Chief
    08/15/2006
  • Pump Performance: Kayo Cavitation

    Checking pump performance curves is one of the first steps in troubleshooting a centrifugal pump problem or seeing if a pump can handle new service conditions. Learn to look for more than just insufficient NPSHA, the common culprit, when investigating cavitation.

    Andrew Sloley, contributing editor
    07/17/2006
  • Keep a steady eye on measurements

    While engineers often strive to keep processes running without too much variation, measurements that don’t change may be a cause for concern not celebration, as one refinery can attest.

    Andrew Sloley, contributing editor
    06/19/2006
  • Pumping Temperature Considerations

    "Bad actor" pumps are those pumps that have trouble with frequent and repetitive failures. In many cases, the source of the problem is an ANSI pump trying valiantly to handle a liquid well beyond the range of its design rating.of 300 degs. F.

    Ross Mackay
    06/19/2006
  • Get a handle on solids’ flow

    Properly accounting for how bulk solids actually will flow in a vessel or overall process can be crucial for successful operations. Learning some simple parameters can often provide a good sense of flowability.

    Don McGlinchey, Glasgow Caledonian University
    05/22/2006
  • Mind Mixer Mechanical Design

    While most mixers can provide a long service life — for instance, some are still operating after more than 30 years — mechanical problems can shorten life or even break parts. In this article, learn about all the mechanical problems that may befall your mixing equipment.

    David S. Dickey, MixTech, Inc.
    04/18/2006
  • Distillation control and optimization, Part 1

    Control columnist Bela Liptak describes the distillation process and PID-based controls, reviews optimization strategies, and shows how advanced controls can cut operating costs of distillation.

    Béla Lipták, PE, Control Columnist
    01/11/2006
  • Flow metering gets more fluid

    There are more and more funcationalities being added to your most trusted instrumentation. These established technologies have expand their reach and performance.

    Mike Spear, editor at large
    01/09/2006
341-360 of 456 < first | | | last >