Articles

181-200 of 246 < first | | | last >
  • Get full value from partial stroking

    There are two main drivers for partial stroking of valves in safety systems: the desire to extend manual test intervals to as long as possible; and to reduce the amount of redundant hardware required for higher safety integrity levels. Like most things in life, it all boils down to one thing: trying to save money.

    Paul Gruhn, ICS Triplex
    03/20/2007
  • Tips and traps

    Following some partial stroke testing tips can make the process easier. Read on for more tips.

    Paul Gruhn, ICS Triplex
    03/20/2007
  • 10 tips for diagnosing control valve problems

    To make the most of diagnostic equipment used in chemical processing, technicians must stretch their knowledge of control valves and related diagnostic equipment that keeps tabs on valve health and safety.

    David W. Douglas
    01/22/2007
  • Find the perfect steam trap

    Consider a variety of factors to select a unit that comes the closest. What steam traps lack in size, they make up for in numbers. In a typical steam plant, their numbers range from several hundred in a large steam plant to more than 20,000 in refinery or chemical complexes.

    Stephen Frank, Richards Industries, Inc.
    01/11/2007
  • How to select control valves, Part 3

    When it comes to selecting and sizing control valves, gain and stability are key characteristics. The non-commercial valve selection chart in this article serves as a reference tool you can download.

    Béla Lipták, Contributing Writer
    12/19/2006
  • Valve innovation helps with nuclear waste

    Valves and actuators designed for handling radioactive waste must meet strict government requirements. This sometimes requires unconventional solutions. Such was the case at the Hanford Waste Treatment Project (WTP), Hanford, Wash.

    Roy Johnson, Flowserve
    12/05/2006
  • Flowmeters clean and dirty

    ControlGlobal.com contributor David W. Spitzer provides a look from a process automation perspective at how magmeters and Venturi meters are vying with ultrasonics for clean and dirty water applications.

    David W. Spitzer
    11/09/2006
  • Avoid trouble with slurries

    Handling slurries (a mix of solids and liquids), should be based on experience and experiments, not theory. Much of the knowledge obtained from pneumatic conveyors and fluidization systems can be used in understanding slurries.

    Thomas R. Blackwood, Healthsite Associates
    11/01/2006
  • Choosing motor controls and drives

    In any industrial control application, using the right drives and motor controls can make or break the project, and also can make a huge difference in how well those applications perform.

    10/18/2006
  • How to select control valves, Part 2

    When it comes to selecting and sizing control valves and positioners, this article not only helps you pick the right one for the right job, but also includes a valuable valve selection chart you can download!

    Béla Lipták, PE, CONTROL Columnist
    10/17/2006
  • The FRETT approach to pump problems

    Some U.S. oil refineries repair their centrifugal pumps every three years while other refineries enjoy an average repair interval of 10 years. Learn about the highest-performing refineries and other petrochemical companies that have significantly reduced pump failures, and how you can obtain the same results.

    Heinz P. Bloch, P.E.
    10/16/2006
  • Increase pump performance

    In this web exclusive on ChemicalProcessing.com, pump expert Ross Mackay says a key to a pump's performance is to look at the control system it's running with.

    Ross Mackay
    09/18/2006
  • Innovations in batching, dosing and weighing

    Challenges brought on by new regulations and technical problems for batching, dosing and weighing have pushed users to find some innovative and surprising solutions beyond our own industry.

    09/05/2006
  • How to select control valves, Part 1

    When it comes to selecting and sizing control valves, the non-commercial chart in this article not only helps you pick the right one for the job, but also serves as a reference tool you can download.

    Béla Lipták, PE, CONTROL Columnist
    08/15/2006
  • Pump Performance: Kayo Cavitation

    Checking pump performance curves is one of the first steps in troubleshooting a centrifugal pump problem or seeing if a pump can handle new service conditions. Learn to look for more than just insufficient NPSHA, the common culprit, when investigating cavitation.

    Andrew Sloley, contributing editor
    07/17/2006
  • Keep a steady eye on measurements

    While engineers often strive to keep processes running without too much variation, measurements that don’t change may be a cause for concern not celebration, as one refinery can attest.

    Andrew Sloley, contributing editor
    06/19/2006
  • Pumping Temperature Considerations

    "Bad actor" pumps are those pumps that have trouble with frequent and repetitive failures. In many cases, the source of the problem is an ANSI pump trying valiantly to handle a liquid well beyond the range of its design rating.of 300 degs. F.

    Ross Mackay
    06/19/2006
  • Mind Mixer Mechanical Design

    While most mixers can provide a long service life — for instance, some are still operating after more than 30 years — mechanical problems can shorten life or even break parts. In this article, learn about all the mechanical problems that may befall your mixing equipment.

    David S. Dickey, MixTech, Inc.
    04/18/2006
  • Pumps benefit from a vane effort

    Widely used but underappreciated, back pump-out vanes extend bearings and seal life.

    Richard Nardone, ITT Industrial & BioPharm Group
    11/15/2005
181-200 of 246 < first | | | last >