181-200 of 249 < first | | | last >
  • Control valves for slurry service

    In this installment of Ask The Experts, noted process control authority and CONTROL Columnist Béla Lipták and his cadre of automation experts answer a reader’s question regarding control valves for slurry services.

  • Optimize pump life cycle

    Understanding an operating system reduces costs and improves reliability. Getting the most out of your pump demands a well-thought-out, holistic strategy.

    Tom Carsten and Barry Erickson, Flowserve
  • Final control

    What’s the latest on control valves? Here's a look at the current marketplace for the final element that all control stuff is aimed at—the control valve that produces the end result.

    Walt Boyes, Editor in Chief
  • Compelling reasons to choose an insertion magnetic flow sensor

    Measuring flow rates and volumes of water and chemicals in the water, wastewater and chemical treatment industries requires the latest, simple to use and cost-effective technology that can keep up with the rigorous demands of the various applications.

  • Make your portable mixer work for you

    Understanding the fundamentals of fluid agitation can help meet the customer’s requirement and the processor’s need for efficiency. While portable mixers have been around for years, they often aren’t used to their full potential. Knowing the basics of mixing and flow patterns can help you get more out of your mixer.

    David Dickey, MixTech, Inc. and Lydia Booth Fenley, Illes Seasonings & Flavors
  • Distillation control and optimization, Part 3

    Control's Béla Lipták continues his series on control of distillation processes, this time focusing on managing reboiler flow, temperature, feed rate, loading and reflux for economy, stability and safety.

    Béla Lipták, PE, CONTROL Columnist
  • Flowmeters clean and dirty contributor David W. Spitzer provides a look from a process automation perspective at how magmeters and Venturi meters are vying with ultrasonics for clean and dirty water applications.

    David W. Spitzer
  • Avoid trouble with slurries

    Handling slurries (a mix of solids and liquids), should be based on experience and experiments, not theory. Much of the knowledge obtained from pneumatic conveyors and fluidization systems can be used in understanding slurries.

    Thomas R. Blackwood, Healthsite Associates
  • Choosing motor controls and drives

    In any industrial control application, using the right drives and motor controls can make or break the project, and also can make a huge difference in how well those applications perform.

  • How to select control valves, Part 2

    When it comes to selecting and sizing control valves and positioners, this article not only helps you pick the right one for the right job, but also includes a valuable valve selection chart you can download!

    Béla Lipták, PE, CONTROL Columnist
  • The FRETT approach to pump problems

    Some U.S. oil refineries repair their centrifugal pumps every three years while other refineries enjoy an average repair interval of 10 years. Learn about the highest-performing refineries and other petrochemical companies that have significantly reduced pump failures, and how you can obtain the same results.

    Heinz P. Bloch, P.E.
  • Increase pump performance

    In this web exclusive on, pump expert Ross Mackay says a key to a pump's performance is to look at the control system it's running with.

    Ross Mackay
  • Remember the old reliable orifice plate

    The cost-effective dP flow meter is ideal for utility surveys, Senior Editor Dirk Willard says in this month's Chemical Processing Field Notes column.

    Dirk Willard, senior editor
  • Keep a steady eye on measurements

    While engineers often strive to keep processes running without too much variation, measurements that don’t change may be a cause for concern not celebration, as one refinery can attest.

    Andrew Sloley, contributing editor
  • Pumping Temperature Considerations

    "Bad actor" pumps are those pumps that have trouble with frequent and repetitive failures. In many cases, the source of the problem is an ANSI pump trying valiantly to handle a liquid well beyond the range of its design rating.of 300 degs. F.

    Ross Mackay
  • Get a handle on solids’ flow

    Properly accounting for how bulk solids actually will flow in a vessel or overall process can be crucial for successful operations. Learning some simple parameters can often provide a good sense of flowability.

    Don McGlinchey, Glasgow Caledonian University
  • Flow metering gets more fluid

    There are more and more funcationalities being added to your most trusted instrumentation. These established technologies have expand their reach and performance.

    Mike Spear, editor at large
  • Pumps benefit from a vane effort

    Widely used but underappreciated, back pump-out vanes extend bearings and seal life.

    Richard Nardone, ITT Industrial & BioPharm Group
  • pH linearization lubricates waste control

    Learn how a simplified technique for linearizing pH can enhance control in waste treatment applications and eliminate the need for gain-adjusting techniques.

181-200 of 249 < first | | | last >