Articles

161-180 of 222 < first | | | last >
  • Equipment & Services: July

    Chemical Processing's Equipment & Services feature provides a variety of production equipment, supplier services and parts.

    07/24/2007
  • Control valves for slurry service

    In this installment of Ask The Experts, noted process control authority and CONTROL Columnist Béla Lipták and his cadre of automation experts answer a reader’s question regarding control valves for slurry services.

    05/01/2007
  • Optimize pump life cycle

    Understanding an operating system reduces costs and improves reliability. Getting the most out of your pump demands a well-thought-out, holistic strategy.

    Tom Carsten and Barry Erickson, Flowserve
    04/30/2007
  • Final control

    What’s the latest on control valves? Here's a look at the current marketplace for the final element that all control stuff is aimed at—the control valve that produces the end result.

    Walt Boyes, Editor in Chief
    04/17/2007
  • Choose the right fluid for your pressure test

    Compressed gas often makes the most sense for checking a process, according to Senior Editor Dirk Willard, in this month's Field Notes column.

    Dirk Willard, senior editor
    04/12/2007
  • Get full value from partial stroking

    There are two main drivers for partial stroking of valves in safety systems: the desire to extend manual test intervals to as long as possible; and to reduce the amount of redundant hardware required for higher safety integrity levels. Like most things in life, it all boils down to one thing: trying to save money.

    Paul Gruhn, ICS Triplex
    03/20/2007
  • Tips and traps

    Following some partial stroke testing tips can make the process easier. Read on for more tips.

    Paul Gruhn, ICS Triplex
    03/20/2007
  • Make your portable mixer work for you

    Understanding the fundamentals of fluid agitation can help meet the customer’s requirement and the processor’s need for efficiency. While portable mixers have been around for years, they often aren’t used to their full potential. Knowing the basics of mixing and flow patterns can help you get more out of your mixer.

    David Dickey, MixTech, Inc. and Lydia Booth Fenley, Illes Seasonings & Flavors
    03/06/2007
  • Flowmeters clean and dirty

    ControlGlobal.com contributor David W. Spitzer provides a look from a process automation perspective at how magmeters and Venturi meters are vying with ultrasonics for clean and dirty water applications.

    David W. Spitzer
    11/09/2006
  • Avoid trouble with slurries

    Handling slurries (a mix of solids and liquids), should be based on experience and experiments, not theory. Much of the knowledge obtained from pneumatic conveyors and fluidization systems can be used in understanding slurries.

    Thomas R. Blackwood, Healthsite Associates
    11/01/2006
  • Choosing motor controls and drives

    In any industrial control application, using the right drives and motor controls can make or break the project, and also can make a huge difference in how well those applications perform.

    10/18/2006
  • How to select control valves, Part 2

    When it comes to selecting and sizing control valves and positioners, this article not only helps you pick the right one for the right job, but also includes a valuable valve selection chart you can download!

    Béla Lipták, PE, CONTROL Columnist
    10/17/2006
  • The FRETT approach to pump problems

    Some U.S. oil refineries repair their centrifugal pumps every three years while other refineries enjoy an average repair interval of 10 years. Learn about the highest-performing refineries and other petrochemical companies that have significantly reduced pump failures, and how you can obtain the same results.

    Heinz P. Bloch, P.E.
    10/16/2006
  • Increase pump performance

    In this web exclusive on ChemicalProcessing.com, pump expert Ross Mackay says a key to a pump's performance is to look at the control system it's running with.

    Ross Mackay
    09/18/2006
  • Keep a steady eye on measurements

    While engineers often strive to keep processes running without too much variation, measurements that don’t change may be a cause for concern not celebration, as one refinery can attest.

    Andrew Sloley, contributing editor
    06/19/2006
  • Pumping Temperature Considerations

    "Bad actor" pumps are those pumps that have trouble with frequent and repetitive failures. In many cases, the source of the problem is an ANSI pump trying valiantly to handle a liquid well beyond the range of its design rating.of 300 degs. F.

    Ross Mackay
    06/19/2006
  • Bend Pressure Drop & Heat Transfer Performance

    The presence of bends and properly predicting pressure drop through them can have a significant impact on accurately estimating the thermal and hydraulic performance of the overall unit.

    LiDong Huang / Fernando J. Aguirre
    02/16/2006
161-180 of 222 < first | | | last >