Process engineering: Particle size reduction techniques and equipment

There are numerous industries that depend on size reduction to improve performance or to meet specifications. This article details size-reduction techniques and equipment that may assist you when handling these materials.

By J. Peter Clark

2 of 2 1 | 2 > View on one page


Figure 2
Figure 2

Wet grinding might be appropriate when the fine particles are to be suspended, as in paint or ink, or where an explosion or dust hazard might exist. The fluid might be water, oil or solvent. Water is used to help suppress dust, but complicates the process if drying is then required. Pigments for inks and paints might be ground in the medium in which they are to be suspended. Wet grinding often takes place in ball, pebble or rod mills. The efficiency of wet grinding can be higher than that for dry grinding, but wear of equipment is also higher [2].

Most size-reduction equipment is subject to heavy wear and therefore parts, such as casing liners, hammers and jaws, are designed for relatively easy replacement.

Process flow schemes
The basic options for size-reduction flow paths are: simple crusher (no separation); normal order circuit (separation after crushing with recycling of overs, that is, oversized material); reverse-order circuit (separation before crushing with only overs going to the crusher and crusher product going back to separation); and reverse order without recycle (separation before crushing but no recycle) [3].

More complex flow sheets are assembled from combinations of these basic flow schemes. Because the particle-size distribution of the feed and milled product is almost always different, it is often advantageous to remove a desired size range before further milling. The trade-off is that more equipment is required, as is additional material handling. When feasible, a vertical equipment arrangement often is preferred so that many flows are driven by gravity. However, this also means that heavy equipment is located on a frame or on a different floor; so, access for maintenance and stabilization against vibration must be considered.

Usually, some form of separation follows size reduction. The most common is simple screening, in which the screen openings are selected to pass the desired size range and retain material that is too large. Because particles rarely are symmetrical, it is important to understand which size characteristics matter. Screens are subject to blinding by particles large enough to enter a hole, but not able to pass through. High-moisture solids can also cause blinding by agglomeration. Most screens are moved by vibration or regular motion to facilitate passage and to remove overs.

Air aspiration is often used, especially in jet mills, to remove fine particles by entrainment while retaining larger particles. Hammer, ball and rod mills frequently have screens on their discharge to retain large particles and media while passing fine particles.

Other separation techniques include froth flotation, in which the difference in surface chemistry between a desired material and waste is exploited to float fine particles attached to air bubbles. The fine particles might be the product or the waste. The remaining material is either enriched or depleted.

Centrifuges or hydroclones, which rely on differences in density and particle size, are also used to separate materials after size reduction. Corn wet mills use both devices to remove starch from protein and fiber.

Sometimes fine particles require agglomeration to provide an appropriate size distribution such as for successful compression of powders into tablets for confections or medications. This process is called granulation and is accomplished by mixing the fines with small amounts of water, solvent or syrup; it might occur with simultaneous drying, heating or cooling.

Special options
Some of the more difficult materials to mechanically process are plastics, rubbers and fibers because they deform, but do not fracture, when struck. One solution is cryogenic milling, in which liquid nitrogen or carbon dioxide is injected with the feed to a hammer mill. The extreme cold makes plastic materials brittle enough to fracture easily. For much the same reason, meat usually is ground at a temperature just above freezing.

A completely different approach to size reduction involves dissolving a material in a solvent and then separating it. One example is spray-drying of fortified dairy beverage mixes. Many chemicals are produced as powders by crystallization. Another example is the use of supercritical carbon dioxide. Upon depressurization, the supercritical fluid loses its high solvent power and precipitates a very fine powder. This approach can be used for heat-sensitive pharmaceuticals and fine chemicals that would be damaged by conventional milling.

No small matter
There are many choices for a size-reduction process, depending upon the feed material, the desired product, hazards, costs and common practices in the given industry. Size-reduction equipment can range from very large and rugged jaw crushers, capable of reducing boulders to sand, to very precise cutting mills. Integration of the correct separation equipment with size-reduction units and attention to solids-flow and material-handling issues are critical to successful design and operation of a size-reduction process.

J. Peter Clark is an Oak Park, Ill.-based consultant who specializes in process development, including size reduction. E-mail him at

1. Abouzeid, A.Z.M., “Processing of Fine Particles in Mineral Beneficiation, Part 1,” Powder Handling and Processing, Vol. 6 (1), pp. 35-48 (1994).
2. Price, M., “Size Reduction” in “Kirk-Othmer Concise Encyclopedia of Chemical Technology,” 4th ed., pp. 1,836-1,838, John Wiley & Sons, New York (1999).
3. Rudd, D.F., G.J. Powers and J.J. Siirola, “Process Synthesis,” pp. 205-208, Prentice-Hall, Englewood Cliffs, N.J. (1973).

2 of 2 1 | 2 > View on one page

Join the discussion

We welcome your thoughtful comments. Please comply with our Community rules.
All comments will display your user name.

Want to participate in the discussion?

Register for free

Log in for complete access.


No one has commented on this page yet.

RSS feed for comments on this page | RSS feed for all comments